Description
The 3M DI-NOC Oak PW-2311MT is one of the wide range of architectural films, that recreates the natural look of expensive materials.
Oak – PW-2311MT – Premium Wood – 3M DI-NOC
PRICE IS PER FULL ROLL FIFTY METERS (MOQ)
PLEASE CALL OUR SALES TEAM ON 01444 500192 TO CHECK STOCK PRIOR TO PLACING YOUR ORDER
Oak – PW-2311MT – Premium Wood – 3M DI-NOC
3M DI-NOC incorporates hundreds of patterns in stock and available by the meter, the range includes wood, solid colours, metallic, glitter, fabric, stone, and leather patterns, they can be used them decoration and refurbishment, these flexible films are simple to use and easy to apply, rated A+ on VOC tests (indoor emissions), as well as being UV and fire-resistant.
Warranty -: 12 years Application Temperature -: From +12°C to +38°C
Storage -: from +4°C to +32°C : 2 years. Length -: 50M
Width -: 1220 mm. Primer -: Primer 94 Solvent Based / WP-2000 Water Based (for porous surfaces)
Kraft Paper Release Liner -: Yes Stretchable -: Yes
Calendared Polymeric -: Yes Interior Installation -: Yes
Outside Installation -: No UV-Resistant -: Yes
Permanent Air Release Adhesive -: Yes Finish: Wood
Thickness -: 200 µm Scratch-Proof -: Average
Suitable Surfaces
3M DI-NOC Interior Films work on various surfaces like paint, varnish, and laminate.
PW-2311MT has a strong sticky adhesive that sticks well to most surfaces.
PW-2311MT also has air channels to help avoid air entrapment and bubbling.
Like smooth plaster, porous surfaces need extra care because they provide good adhesion.
For surfaces such as these, the use of Primer 94 is essential on non-porous surfaces & WP-2000 Water Based Primer for Porous surface.
For surfaces that need particular care and attention before installation include unsealed concrete.
PVC films and metals that can corrode such as copper will be less suitable for the product.
Smooth surfaces like glass or metal stick best and look nicer.
Slightly textured surfaces offer good adhesion.
Texture may be visible in some finishes.
Heavily textured wallpapers, brick, and concrete block surfaces won’t provide full adhesion coverage.
The texture of the surface will show through the film.
Paints now contain fewer VOCs and additives that make them easy to clean.
These changes may affect how well the adhesive sticks to the painted surface.
Before installing PW-2311MT, clean the area with Isopropyl 70/30 to improve the bond.
Thorough cleaning is necessary for vinyl wrap installation.
The use of Primer 94 or WP-2000 (porous surfaces) will also help to overcome any adhesion issues.
You can also use thin test strips on the area where you’re applying it to improve adhesion.
This will help you determine what steps to take next, like using a primer.
Adhesion
Before you apply the Interior Film, make sure to repair any holes or chips.
Thoroughly clean the surface with Isopropyl 70/30 Alcohol Rubbing Gel Spray.
Use a microfiber cloth for best results.
Paint or primer needs to be fully cured.
A primer coat needs to be applied and fully cured on porous surfaces.
Certain types of MDF grades are very porous, which means they might need more than one coat of WP-2000 Water Based Primer.
This depends on how well the surface absorbs the paint.
You can also sand roughen MDF, wood, Melamine, and plastics to help them stick better.
Surface Preparation
Damaged areas with holes and chips need to be repaired before applying the Interior Film.
Clean the application surface thoroughly with an Isopropyl 70/30 Alcohol Rubbing Gel Spray using a microfiber cloth.
A primer coat needs to be applied and fully cured for porous surfaces.
Some very porous surfaces such as certain MDF grades may require more than 1 coat depending on the absorbency of the surface.
MDF, Wood, Melamine, and low surface energy plastics can be roughened up with sandpaper to aid adhesion.
Application
The recommended application temperature for PW-2311MT is 54ºC.
Cut the film to size with a minimum of 25mm extra on all sides for trimming.
Use a squeegee with a felt to smooth out the initial point of contact.
Align the Interior film with the application surface and pull off a maximum of 300mm of liner.
Then starting in the centre, squeegee the film down using overlapping strokes.
Remove another 300mm of liner.
Repeat this process until the application surface is completely covered.
Be careful to apply the film just once.
Moving it again and again can make the film separate.
Stretching of the film can cause colour and pattern variation.
Squeegee the entire area again to ensure 100% adhesion.
Using a hot air gun will help ensure 100% adhesive contact and improve the bond.
If air is trapped causing a bubble during installation, strip back the film gently, then reapply with the plastic applicator.
Very small air bubbles can also be released by pricking the bubble with a pin.
Likewise if you press out the entrapped air by moving your thumb toward the puncture hole.
Primer
We recommend WP-2000 Primer for the following -:
Gypsum Plasterboard.
Calcium Silicate Board.
Concrete.
Painted Walls.
Stone.
Wood.
Melamine.
Polyester Coated Laminates.
Plastisol Coated Metals.
MDF and low surface energy plastics such as Polypropylene and Polyethylene.
A primer will also help prevent issues in the film’s most stressed areas.
These areas are prone to heat and stretching during the application process.
Furthermore Doors’ edges and tops, curved surfaces, corners, and overlapping joints need this treatment.
Primer 94 was made for PVC films, especially for connecting joints.
In addition, it works well with wood, gypsum, etc.
In addition multiple coatings are recommended for very porous surfaces.
Oak
Average rating: 0 reviews
Related